Руководство Hitachi G 10SD2 Углошлифовальная машина

Руководство

5

English

7. The wheel continues to rotate after the tool is switched

off .

After switching off the machine, do not put it down until

the depressed center wheel has come to a complete

stop. Apart from avoiding serious accidents, this

precaution will reduce the amount of dust and swarf

sucked into the machine.

8. When the machine is not use, the power source should

be disconnected.

9. Be sure to switch OFF and disconnect the attachment

plug from the receptacle to avoid a serious accident

before the depressed center wheel is assembling and

disassembling.

10. RCD

The use of a residual current device with a rated residual

current of 30 mA or less at all times is recommended.

SYMBOLS

WARNING

The following show symbols used for the machine.

Be sure that you understand their meaning before

use.

G10SD2 / G12S2 / G13SD: Disc Grinder

Read all safety warnings and all instructions.

Always wear eye protection.

Only for EU countries

Do not dispose of electric tools together with

household waste material!

In observance of European Directive 2002/96/

EC on waste electrical and electronic equipment

and its implementation in accordance with

national law, electric tools that have reached

the end of their life must be collected separately

and returned to an environmentally compatible

recycling facility.

V Rated voltage

Alternating current

P

Power input

n

Rated speed

min

-1

Revolution or reciprocations per minute

D Wheel outer diameter

d Wheel hole diameter

t Wheel thickness

Peripheral speed

kg

Weight (Only main body)

Ϩ

Switching ON

Switching OFF

Disconnect mains plug from electrical outlet

Warning

Class II tool

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package

contains the accessories listed in the below.

○ Wrench .........................................................................1

○ Side handle ...................................................................1

○ Depressed center wheel ...............................................1

Standard accessories are subject to change without notice.

APPLICATIONS

○ Removal of casting fi n and fi nishing of various types of

steel, bronze and aluminum materials and castings.

○ Grinding of welded sections or sections cut by means of

a cutting torch.

○ Grinding of synthetic resins, slate, brick, marble, etc.

○ Cutting of synthetic concrete, stone, brick, marble, and

similar materials.

SPECIFICATIONS

The specifi cations of this machine are listed in the Table on

page 134.

NOTE

Due to HITACHI’s continuing program of research and

development, the specifi cations herein are subject to

change without prior notice.

MOUNTING AND OPERATION

Action Figure Page

Fitting and adjusting the wheel guard 1 135

Fixing the side handle 2 135

Assembling depressed center wheel 3 135

Assembling cutting wheel 4 135

Switch operation 5 136

Grinding angle and grinding method 6 136

Replacing carbon brushes 7 136

Selecting accessories ― 137

MAINTENANCE AND INSPECTION

1. Inspecting the depressed center wheel

Ensure that the depressed center wheel is free of cracks

and surface defects.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Inspecting the carbon brushes (Fig. 7)

The motor employs carbon brushes which are

consumable parts. Since an excessively worn carbon

brush can result in motor trouble, replace the carbon

brushes with new ones having the same carbon brush

No. ⓐ shown in the fi gure when it becomes worn to or

near the “wear limit” ⓑ. In addition, always keep carbon

brushes clean and ensue that they slide freely within the

brush holders.

4. Replacing carbon brushes (Fig. 7)

⟨Disassembly⟩

(1) Loosen the D4 tapping screw ⓒ retaining the tail cover

ⓓ and remove the tail cover.

0000Book̲G10SD2.indb50000Book̲G10SD2.indb5 2014/10/319:11:462014/10/319:11:46

Рейтинг

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего Hitachi G 10SD2 Углошлифовальная машина. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с Hitachi. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего Hitachi G 10SD2 Углошлифовальная машина на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Все инструкции для Hitachi Углошлифовальные машины
Больше руководств Углошлифовальные машины

Часто задаваемые вопросы о Hitachi G 10SD2 Углошлифовальная машина

Наша служба поддержки выполняет поиск полезной информации по изделиям и отвечает на часто задаваемые вопросы. Если вы заметили неточность в наших часто задаваемых вопросах, сообщите нам об этом с помощью нашей контактной формы.

Сопутствующие товары

Руководство

Hitachi G 18UC Углошлифовальная машина

Руководство

Hitachi G 18SH2 Углошлифовальная машина

Руководство

Ryobi RAG18125-0 Углошлифовальная машина

Руководство

Redverg AG650-115 Углошлифовальная машина

Руководство

Вихрь УШМ-230/2300 Углошлифовальная машина

Руководство

Einhell TC-AG 115/750 Углошлифовальная машина

Руководство

Sparky MBA 2400PA HD Углошлифовальная машина

Руководство

Rodex RDX104 Углошлифовальная машина

Связанные категории