Руководство Hitachi G 10SD2 Углошлифовальная машина

Руководство

6

English

(2) Use the auxiliary hexagonal wrench or small screwdriver

to pull up the edge of the spring ⓔ that is holding down

the carbon brush. Remove the edge of the spring toward

the outside of the brush holder ⓕ.

(3) Remove the end of the pig-tail ⓖ on the carbon brush

ⓗ from the terminal section of brush holder and then

remove the carbon brush from the brush holder.

⟨Assembly⟩

(1) Insert the end of the pig-tail of the carbon brush in the

terminal section of brush holder.

(2) Insert the carbon brush in the brush holder.

(3) Use the auxiliary hexagonal wrench or small screwdriver

to return the edge of the spring to the head of the carbon

brush.

(4) Mount the tail cover and tighten the D4 tapping screw.

5. Replacing supply cord

If the replacement of the supply cord is necessary, it has

to be done by Hitachi Authorized Service Center to avoid

a safety hazard.

6. Maintenance of the motor

WARNING

Always wear protective goggles and dust respirators

when blowing air from the tail cover air hole with the use

of an air gun, etc.

Failure to observe this may result in ejected dust being

inhaled or entering your eyes.

The motor unit winding is the very “heart” of the power tool.

Exercise due care to ensure the winding does not become

damaged and/or wet with oil or water.

NOTE

When work has been fi nished, blow air containing no

moisture from the tail cover air hole with the use of an

air gun, etc., while running the motor without any load

applied. This is eff ective in removing any dirt and dust

that has accumulated. Dirt and dust collecting inside the

motor may result in malfunctions.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country specifi c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a Hitachi Authorized Service Center.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue: — Neutral

Brown: — Live

As the colours of the wires in the main lead of this tool may

not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black. The wire

coloured brown must be connected to the terminal marked

with the letter L or coloured red. Neither core must be

connected to the earth terminal.

NOTE:

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except The United Kingdom.

Information concerning airborne noise and vibration

The measured values were determined according to

EN60745 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 95 dB (A).

Measured A-weighted sound pressure level: 84 dB (A).

Uncertainty K: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN60745.

Surface grinding:

Vibration emission value

a

h

,

AG

= 6.1 m/s

2

Uncertainty K = 1.5 m/s

2

The declared vibration total value has been measured in

accordance with a standard test method and may be used

for comparing one tool with another.

It may also be used in a preliminary assessment of exposure.

WARNING

○ The vibration emission during actual use of the power

tool can diff er from the declared total value depending in

the ways in which the tool is used.

○ Identify safety measures to protect the operator that

are based on an estimation of exposure in the actual

conditions of use (taking account of all parts of the

operating cycle such as the times when the tool is

switched off and when it is running idle in addition to the

trigger time).

NOTE

Due to HITACHI’s continuing program of research and

development, the specifi cations herein are subject to

change without prior notice.

0000Book̲G10SD2.indb60000Book̲G10SD2.indb6 2014/10/319:11:462014/10/319:11:46

Рейтинг

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего Hitachi G 10SD2 Углошлифовальная машина. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с Hitachi. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего Hitachi G 10SD2 Углошлифовальная машина на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Все инструкции для Hitachi Углошлифовальные машины
Больше руководств Углошлифовальные машины

Часто задаваемые вопросы о Hitachi G 10SD2 Углошлифовальная машина

Наша служба поддержки выполняет поиск полезной информации по изделиям и отвечает на часто задаваемые вопросы. Если вы заметили неточность в наших часто задаваемых вопросах, сообщите нам об этом с помощью нашей контактной формы.

Сопутствующие товары

Руководство

Hitachi G 18UC Углошлифовальная машина

Руководство

Hitachi G 18SH2 Углошлифовальная машина

Руководство

Redverg AG650-115 Углошлифовальная машина

Руководство

Skil 9020 AA Углошлифовальная машина

Руководство

Sparky MB 1300PA HD Углошлифовальная машина

Руководство

Sparky MBA 2600P HD Углошлифовальная машина

Руководство

Redverg RD-AG73-115 Углошлифовальная машина

Руководство

Alteco AG 850-125.1 Углошлифовальная машина

Связанные категории