Руководство Hitachi G 10SD2 Углошлифовальная машина

Вам нужно руководство для вашего Hitachi G 10SD2 Углошлифовальная машина? Ниже вы можете бесплатно просмотреть и скачать PDF-инструкцию на русском языке. В настоящее время этот продукт имеет 4 часто задаваемых вопроса, 0 комментариев и имеет 0 голосов. Если это не то руководство, которое вам нужно, свяжитесь с нами.

Ваше устройство неисправно, и в руководстве отсутствует решение? Перейдите в Repair Café для получения бесплатных ремонтных услуг.

Руководство

Loading…

4
English
b) The grinding surface of centre depressed wheels
must be mounted below the plane of the guard lip.
An improperly mounted wheel that projects through the
plane of the guard lip cannot be adequately protected.
c)
The guard must be securely attached to the power
tool and positioned for maximum safety, so the least
amount of wheel is exposed towards the operator.
The guard helps to protect the operator from broken
wheel fragments, accidental contact with wheel and
sparks that could ignite clothing.
d) Wheels must be used only for recommended
applications. For example: do not grind with the
side of cut-o wheel.
Abrasive cut-o wheels are intended for peripheral
grinding, side forces applied to these wheels may cause
them to shatter.
e) Always use undamaged wheel anges that are of
correct size and shape for your selected wheel.
Proper wheel anges support the wheel thus reducing
the possibility of wheel breakage. Flanges for cut-o
wheels may be di erent from grinding wheel anges.
f) Do not use worn down wheels from larger power
tools.
Wheel intended for larger power tool is not suitable for
the higher speed of a smaller tool and may burst.
ADDITIONAL SAFETY WARNINGS
SPECIFIC FOR ABRASIVE CUTTING-
OFF OPERATIONS
a) Do not “jam” the cut-o wheel or apply excessive
pressure. Do not attempt to make an excessive
depth of cut.
Overstressing the wheel increases the loading and
susceptibility to twisting or blinding of the wheel in the
cut and the possibility of kickback or wheel breakage.
b) Do not position your body in line with and behind
the rotating wheel.
When the wheel, at the point of operation, is moving
away from your body, the possible kickback may propel
the spinning wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a cut
for any reason, switch o the power tool and hold
the power tool motionless until the wheel comes to
a complete stop. Never attempt to remove the cut-
o wheel from the cut while the wheel is in motion
otherwise kickback may occur.
Investigate and take corrective action to eliminate the
cause of wheel binding.
d) Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully re-enter
the cut.
The wheel may bind, walk up or kickback if the power
tool is restarted in the workpiece.
e) Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near the
line of cut and near the edge of the workpiece on both
sides of the wheel.
f) Use extra caution when making a “pocket cut” into
existing walls or other blind areas.
The protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause kickback.
GENERAL SAFETY INSTRUCTIONS
FOR GRINDERS
Check that speed marked on the wheel is equal to or
greater than the rated speed of the grinder;
Ensure that the wheel dimensions are compatible with
the grinder;
Abrasive wheels shall be stored and handled with care in
accordance with manufacturer’s instructions;
Inspect the grinding wheel before use, do not use
chipped, cracked or otherwise defective products;
Ensure that mounted wheels and points are tted in
accordance with the manufacturer’s instructions;
Ensure that blotters are used when they are provided
with the bonded abrasive product and when they are
required;
Ensure that the abrasive product is correctly mounted
and tightened before use and run the tool at no-load for
30 seconds in a safe position, stop immediately if there
is considerable vibration or if other defects are detected.
If this condition occurs, check the machine to determine
the cause;
If a guard is equipped with the tool never use the tool
without such a guard;
When using a abrasive cutting wheel, be sure to remove
the standard accessory wheel guard and attach the
wheel guard with side guard (sold separately) (Fig. 4);
Do not use separate reducing bushings or adapters to
adapt large hole abrasive wheels;
For tools intended to be tted with threaded hole wheel,
ensure that the thread in the wheel is long enough to
accept the spindle length;
Check that the work piece is properly supported;
Do not use cutting o wheel for side grinding;
Ensure that sparks resulting from use do not create
a hazard e.g. do not hit persons, or ignite ammable
substances;
Ensure that ventilation openings are kept clear when
working in dusty conditions, if it should become
necessary to clear dust, rst disconnect the tool from
the mains supply (use non metallic objects) and avoid
damaging internal parts;
Always use eye and ear protection. Other personal
protective equipment such as dust mask, gloves, helmet
and apron should be worn;
Pay attention to the wheel that continues to rotate after
the tool is switched o .
ADDITIONAL SAFETY WARNINGS
1. Ensure that the power source to be utilized conforms
to the power requirements speci ed on the product
nameplate.
2. Ensure that the power switch is in the OFF position. If the
plug is connected to a receptacle while the power switch
is in the ON position, the power tool will start operating
immediately, which could cause a serious accident.
3. When the work area is removed from the power source,
use an extension cord of su cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Ensure that the depressed center wheel to be utilized is
the correct type and free of cracks or surface defects.
Also ensure that the depressed center wheel is properly
mounted and the wheel nut is securely tightened.
5. Con rm that the push button is disengaged by pushing
push button two or three times before switching the
power tool on.
6. To prolong the life of the machine and ensure a rst
class nish, it is important that the machine should not
be overloaded by applying too much pressure. In most
applications, the weight of the machine alone is su cient
for e ective grinding. Too much pressure will result in
reduced rotational speed, inferior surface nish, and
overloading which could reduce the life of the machine.
0000Book̲G10SD2.indb40000Book̲G10SD2.indb4 2014/10/319:11:462014/10/319:11:46
Загрузить руководство на русскийском (PDF, 7.58 MB)
(Помните о необходимости охраны окружающей среды и распечатывайте настоящее руководство только в том случае, если это действительно необходимо)

Loading…

Рейтинг

Сообщите нам, что вы думаете о Hitachi G 10SD2 Углошлифовальная машина, оставив оценку продукта. Хотите поделиться вашими впечатлениями от данного изделия или задать вопрос? Вы можете оставить комментарий в нижней части страницы.
Вы довольны Hitachi G 10SD2 Углошлифовальная машина?
Да Нет
Будьте первым, кто оценит это изделие
0 голоса

Присоединиться к беседе по данному изделию

Здесь вы можете поделиться тем, что думаете о Hitachi G 10SD2 Углошлифовальная машина. Если у вас есть вопросы, сначала внимательно прочтите инструкцию. Запросить руководство можно с помощью контактной формы.

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего Hitachi G 10SD2 Углошлифовальная машина. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с Hitachi. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего Hitachi G 10SD2 Углошлифовальная машина на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Бренд Hitachi
Модель G 10SD2
Категория Углошлифовальные машины
Тип файла PDF
Размер файла 7.58 MB

Все инструкции для Hitachi Углошлифовальные машины
Больше руководств Углошлифовальные машины

Часто задаваемые вопросы о Hitachi G 10SD2 Углошлифовальная машина

Наша служба поддержки выполняет поиск полезной информации по изделиям и отвечает на часто задаваемые вопросы. Если вы заметили неточность в наших часто задаваемых вопросах, сообщите нам об этом с помощью нашей контактной формы.

На каких материалах я могу использовать угловую шлифовальную машину. Проверенный

Угловые шлифовальные машины лучше всего подходят для обработки металла или камня. Машины выделяют много тепла и поэтому менее подходят для работы с деревом или пластиком.

Это было полезно (63) Читать далее

Нужно ли мне носить средства защиты органов слуха при использовании угловой шлифовальной машины? Проверенный

Да, ты должен. Хотя уровень шума, производимого угловой шлифовальной машиной, может варьироваться в зависимости от марки и модели, длительное воздействие громкого шума может привести к необратимому повреждению слуха. Вот почему рекомендуется использовать средства защиты органов слуха.

Это было полезно (16) Читать далее

Нужно ли мне носить защитные очки при использовании угловой шлифовальной машины? Проверенный

Да. При измельчении мелкие частицы могут взлетать. Попадая в глаз, они могут вызвать необратимое повреждение глаз. Вот почему всегда необходимо носить защитные очки.

Это было полезно (14) Читать далее

Можно ли хранить электроинструменты в сарае или гараже? Проверенный

В общем, хранить электроинструменты можно в сарае или гараже, даже если там иногда замерзает. Однако для продления срока службы электроинструмента лучше хранить его в сухом месте без сильных колебаний температуры. В сарае или гараже разница температур может привести к образованию конденсата, который может вызвать ржавчину. Кроме того, инструменты, работающие от аккумуляторов, служат меньше и плохо заряжаются при очень низких температурах. Чтобы знать, как следует хранить ваш электроинструмент, всегда внимательно читайте руководство пользователя.

Это было полезно (5) Читать далее
Руководство Hitachi G 10SD2 Углошлифовальная машина

Сопутствующие товары

Связанные категории