Руководство Vivanco UR 4 SL Пульт дистанционного управления

Руководство

UR 4 SL UNIVERSAL CONTROLLER

Vivanco GmbH, D-22926 Ahrensburg, E-Mail

: [email protected]

, Helpline: +49 (0) 4102 231135

2

(GB) Instructions

VIVANCO UR 4 SL remote control for

almost all TV, audio, video and other

infrared-controllable appliances

Inserting the batteries

Open the battery compartment on the

underside of the UR, see Fig.. Then insert 1

new CR 2032 lithium battery. Make sure that

the polarity is correct: the "+" and "-" markings

on the batteries and in the compartment must

match. To check functionality, press the PWR

button. If everything is correct the red lamp

flickers when the button is pressed.

Lithium Battery:

Caution: Danger of explosion if battery is

incorrectly replaced. Replace only with the

same or equivalent type recommended by the

manufacturer. Dispose of used batteries

according to the manufacturer’s instructions.

Adapting to appliances

In order to control your appliances you must

adapt or set the remote control to them:.

Direct control code entry using the

enclosed list

Example: setting to control a Panasonic

television set:

1. The attached list gives, for

example, the Panasonic Code 176.

Please make sure you have selected the

correct list for television sets (TV).

2. To prepare code entry, press the

SET button, keep it pressed and then press the

required appliance button, e.g. TV, additionally

until the lamp (LED) lights constantly.

3. Then press the number buttons

(e.g. 1 7 6) in sequence.

4. Once the numbers have been

entered the lamp goes out and the remote

control is ready to control your appliance.

5. Finally, test the control code setting

by trying to control (in this example) your

television set. If it does not work at all or not

correctly try a different code from the list or the

code search (see below).

To set the remote control for other appliances,

proceed in the same way. Instead of the TV

appliance button, press another button e.g.

DVB (SAT, DECODER, DVB-T), DVD, AUX.

The letters on the device buttons TV, DVB,

DVD, AUX are for your orientation only. You

can set each type of device under any of the

buttons.

You can terminate the mode by pressing any

device button.

Code search

If the brand of your appliance is not in the list

or none of the codes given fits, we recommend

a code search.

Manual code search

1. Switch on the appliance to be

controlled. Program is running.

2. To prepare code search, press the

SET button, keep it pressed and then press the

required appliance button, e.g. TV, additionally

until the lamp (LED) lights constantly.

3. Then point the remote control at the

appliance to be controlled.

4. Briefly press the SET button once.

The lamp (LED) blinks. – Except when

searching for a TV code you can also briefly

press the (Play) button and use the Play

function to help search and press ON/OFF

for testing the next code. Make sure that a

tape, a DVD or a CD is inserted in the tape

deck, player or recorder.

5. Press the ON/OFF (appliance

on/off) button repeatedly for testing the next

code, approx. every 1,5 seconds, until the

appliance, e.g. your TV reacts by power off or

your DVD player, reacts by Play > button. - If

your appliance has switched itself off you must

switch it back on again, e.g. on the appliance

or with the original remote control, to continue

searching. - When your appliance reacts you

can also try out other buttons without

interrupting the search. If some buttons do not

work properly, simply continue searching with

ON/OFF or Play.

6. When your appliance reacts

correctly, press the appliance button, e.g. TV,

and end the search. The lamp (LED) goes out.

- The UR 4 SL continues with the search at the

point where you interrupted it. . The code last

entered remains stored. The search stops after

approx. 30 seconds of inactivity.

Automatic code search

Your remote control finds the correct settings

almost automatically in seconds:

1. Switch on the appliance to be

controlled. A channel number, for example,

appears in the display of your satellite receiver.

2. To start the code search, press the

required appliance button, e.g. TV briefly.

3. Then press SET for about 5

seconds until the lamp (LED) starts to blink.

4. Then point the remote control at the

appliance to be controlled while the remote

control emits a different ON/OFF signal every

second.

Рейтинг

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего Vivanco UR 4 SL Пульт дистанционного управления. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с Vivanco. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего Vivanco UR 4 SL Пульт дистанционного управления на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Все инструкции для Vivanco Пульты дистанционного управления
Больше руководств Пульты дистанционного управления

Часто задаваемые вопросы о Vivanco UR 4 SL Пульт дистанционного управления

Наша служба поддержки выполняет поиск полезной информации по изделиям и отвечает на часто задаваемые вопросы. Если вы заметили неточность в наших часто задаваемых вопросах, сообщите нам об этом с помощью нашей контактной формы.

Сопутствующие товары

Руководство

Vivanco UR 820 LCD Пульт дистанционного управления

Руководство

Vivanco UR Z2 Пульт дистанционного управления

Руководство

Vivanco UR 82 SE Пульт дистанционного управления

Руководство

Vivanco UR 12 N Пульт дистанционного управления

Руководство

Vivanco UR 03 UF Пульт дистанционного управления

Руководство

Vivanco Viv.Control 5 Пульт дистанционного управления

Руководство

Vivanco UR 100 LCD Пульт дистанционного управления

Руководство

Vivanco UR Zap 2 Пульт дистанционного управления

Связанные категории