Руководство Skil 5740 CA Циркулярная пила

Руководство

11

• Adjusting cutting angle (0-45°) 6

- loosen knob L

- tilt tool until desired cutting angle is set on scale using

indicator M

- tighten knob L

! when bevel cutting, cutting depth does not

correspond with value on cutting depth scale

• 90° Cutting angle check 6

- adjust and tighten foot J to maximum cutting depth 5

- adjust and tighten cutting angle to 0°

- check for a 90° angle between the blade and bottom of

foot with a square

- if adjustment is needed, tilt and tighten foot to 45° and

bend tab N with an adjustable wrench

• Adjustable saw line visor P 7a

- for guiding tool along desired line of cut marked on the

workpiece

- for a straight 0° cut or a 45° bevel cut use the indicator

line concerned

! the wide part of the foot should rest on the

supported part of the workpiece

- can be adjusted to allow you to choose whether waste

material is on inner or outer side of blade 7b

! cutting width is determined by width of blade

teeth and not by width of blade body

! always make trial cuts first to verify actual line of

cut

• Dust suction

- connect vacuum cleaner to extension Q 8

! never let the vacuum cleaner hose interfere with

the lower guard or the cutting operation

- one may also use a dust bag (SKIL accessory

2610387402)

! do not use dustbag/vacuum cleaner when cutting

metal

• Operating the tool 8

- connect plug to power source

- always hold handle R rmly with one hand and handle

S rmly with the other hand

- place tool with front end of foot at on workpiece

! ensure that the saw teeth are not engaged into

the workpiece

- switch on tool by rst pressing knob T (= safety switch

which cannot be locked) and then pulling trigger U

! the tool should run at full speed before the blade

enters into the workpiece

- lower guard C opens automatically when saw blade

enters the workpiece (open lower guard manually by

using lever D only for special cuts such as plunge cuts)

! do not force the tool (apply light and continuous

pressure in order to avoid overheating the blade tips

and, in case of cutting plastics, melting the plastic

material)

! while working, always hold the tool at the

grey-coloured grip area(s)

- after completing the cut switch o tool by releasing

trigger U

! ensure that the blade has come to a complete

standstill, before you lift the tool from the workpiece

APPLICATION ADVICE

• Always face the good side of the workpiece down to

ensure minimum splintering

• When using guide-rail (SKIL accessory 2610Z04064) in

combination with adapter, the depth of cut will be

reduced with 14 mm for 90° as well as 45° cuts

• Only use sharp saw blades of the correct type 9

- quality of cut improves by the number of teeth

- carbide tipped blades stay sharp up to 30 times longer

than ordinary blades

• Rip fence V 0

- for making exact cuts along a workpiece edge

- can be inserted in either side of foot

Adjusting rip fence

- adjust to desired cutting width by using rip fence scale

(use saw line visor P as 0-reference)

- loosen knob W

- tighten knob W

• Plunge cutting !

- set desired cutting depth

- tilt tool forward with saw line visor P lined up with

desired line of cut marked on the workpiece

- open lower guard C with lever D

- just before blade enters workpiece, switch on tool and

gradually lower back end of tool using front end of foot

as hinge-point

- gradually move tool downward as well as forward

- as soon as blade enters the material, release lever D

! never pull tool backwards

• Cutting large panels @

- support panel close to the cut either on oor, table or

workbench

! set cutting depth so that you cut through panel

and not through support

- in case rip fence does not allow desired width of cut,

clamp or nail straight piece of wood to workpiece as a

guide, and use the right side of the foot against this

guide

• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool and cord clean (especially the

ventilation slots)

! disconnect the plug before cleaning

• Always keep the area around lower guard C 3 clean

(remove dust and chips by blowing out with compressed

air or with a brush)

• Clean saw blade immediately after use (especially from

resin and glue)

• If the tool should fail despite the care taken in manufacturing

and testing procedures, repair should be carried out by an

after-sales service centre for SKIL power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skil.com)

Рейтинг

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего Skil 5740 CA Циркулярная пила. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с Skil. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего Skil 5740 CA Циркулярная пила на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Все инструкции для Skil Циркулярные пилы
Больше руководств Циркулярные пилы

Часто задаваемые вопросы о Skil 5740 CA Циркулярная пила

Наша служба поддержки выполняет поиск полезной информации по изделиям и отвечает на часто задаваемые вопросы. Если вы заметили неточность в наших часто задаваемых вопросах, сообщите нам об этом с помощью нашей контактной формы.

Сопутствующие товары

Руководство

Skil 3520 DA Циркулярная пила

Руководство

Skil 5255 AA Циркулярная пила

Руководство

Skil 5765 AA Циркулярная пила

Руководство

Skil 5165 AA Циркулярная пила

Руководство

Skil 3540 FA Циркулярная пила

Руководство

Skil 5064 Циркулярная пила

Руководство

Skil 5665 AA Циркулярная пила

Руководство

Skil 3571 FA Циркулярная пила

Связанные категории