Руководство Skil 5164 Циркулярная пила

Руководство

● SKIL can assure flawless functioning of the tool only

when original accessories are used

● Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

● Never use the tool without the original protection guard

system

● This tool should not be used by people under the age of

16 years

● The noise level when working can exceed 85 dB(A);

wear ear protection

● If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

● Never use tool when cord is damaged; have it replaced

by a qualified person

● Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

● This tool is not suitable for wet cutting

● After switching off your circular saw, never stop the

rotation of the saw blade by a lateral force applied

against it

● Never use circular saw blades made of high speed steel

(HSS)

● Never use grinding/cutting discs with this tool

● Do not cut material containing asbestos

● Wear a dust protection mask when working with

materials which produce dust that is detrimental to

health; inform yourself beforehand about the materials to

be worked on

● Do not attempt to cut extremely small workpieces

● Remove all obstacles on top of as well as underneath

the cutting path before you start cutting

● Do not work overhead with the tool

● Only use a saw table provided with a switch that

prevents restarting of the motor after interruption of

voltage

● Only use a saw table provided with a kerf guide

● Always disconnect plug from power source before

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

● Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

● If for any reason the old plug is cut off the cord of this

tool, it must be disposed of safely and not left unattended

USE

● Changing saw blade 3

- open lower guard A by using lever B

- change saw blade with saw teeth and arrow printed

on saw blade pointing in same direction as arrow on

lower guard A

! make sure that clamping surfaces C of flanges are

perfectly clean and face the blade

- tighten blade bolt D with hex key 1/8 turn past finger

tight (ensures slippage of saw blade when it

encounters excessive resistance thus reducing motor

overload and saw kickback)

● Adjusting cutting depth (0-64 mm) 4

- for an optimal quality cut the saw blade should not

extend more than 3 mm below the workpiece

- loosen lever E

- raise/lower foot F until desired cutting depth is set on

scale using indicator G

- tighten lever E

● Adjusting cutting angle (0-45°) 5

- loosen knob H

- tilt tool until desired cutting angle is set on scale using

indicator J

- tighten knob H

! when bevel cutting, cutting depth does not

correspond with value on cutting depth scale

● 90° Cutting angle check 5

- adjust and tighten foot F to maximum cutting depth 4

- adjust and tighten cutting angle to 0°

- check for 90° angle between the blade and bottom of

foot with a square

- if adjustment is needed, tilt and tighten foot to 45° and

bend tab K with an adjustable wrench

● Line-of-cut indicator L 6a

- for guiding tool along desired line of cut marked on the

workpiece

- for a straight 0° cut or a 45° bevel cut use the indicator

line concerned

! the wide part of the foot should rest on the

supported part of the workpiece

- can be adjusted to allow you to choose whether waste

material is on inner or outer side of blade 6a+b

! cutting width is determined by width of blade

teeth and not by width of blade body

! always make trial cuts first to verify actual line of

cut

● Dust suction

- connect vacuum cleaner to extension M 2

! never let the vacuum cleaner hose interfere with

the lower guard or the cutting operation

- one may also use a dust bag (SKIL accessory

2610387402)

● Operating the tool 2

- connect plug with power source

- always hold handle N firmly with one hand and

handle P firmly with the other hand

- place tool with front end of foot flat on workpiece

! ensure that the saw teeth are not engaged into the

workpiece

- switch on tool by first pressing knob Q (= safety switch

which cannot be locked) and then pulling trigger R

! the tool should run at full speed before the blade

enters into the workpiece

- lower guard A opens automatically when saw blade

enters the workpiece (open lower guard manually by

using lever B only for special cuts such as plunge

cuts)

- do not force the tool; apply light and continuous

pressure

- after completing the cut switch off tool by releasing

trigger R

10

5164_EU.qxd 19-02-2004 09:52 Pagina 10

Рейтинг

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего Skil 5164 Циркулярная пила. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с Skil. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего Skil 5164 Циркулярная пила на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Все инструкции для Skil Циркулярные пилы
Больше руководств Циркулярные пилы

Часто задаваемые вопросы о Skil 5164 Циркулярная пила

Наша служба поддержки выполняет поиск полезной информации по изделиям и отвечает на часто задаваемые вопросы. Если вы заметили неточность в наших часто задаваемых вопросах, сообщите нам об этом с помощью нашей контактной формы.

Сопутствующие товары

Руководство

Skil 5165 AA Циркулярная пила

Руководство

Skil 5765 AA Циркулярная пила

Руководство

Skil 3550 CA Циркулярная пила

Руководство

Skil 5140 Циркулярная пила

Руководство

Skil 3571 DA Циркулярная пила

Руководство

Skil 5751 Циркулярная пила

Руководство

Skil 3520 FA Циркулярная пила

Руководство

Skil 5265 AD Циркулярная пила

Связанные категории