Руководство Skil 2550 CA Циркулярная пила

Руководство

12

ADDITIONAL SAFETY WARNINGS

GENERAL

• This tool should not be used by people under the age of

16 years

• This tool is not suitable for wet cutting

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic

(such as oak and beech dust) especially in conjunction

with additives for wood conditioning; wear a dust

mask and work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Do not use this saw in combination with a saw table

• Remove battery from tool before making any adjustments

or changing accessories

ACCESSORIES

• SKIL can assure awless functioning of the tool only

when original accessories are used

• Use only saw blades that correspond with the

characteristic data given in these operation instructions

and that are tested and marked in accordance with EN

847-1

• Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

• Use only saw blades with a minimum diameter of 140

mm, a maximum diameter of 140 mm and a spindle hole

of 10 mm

• Never use saw blades made of high speed steel (HSS)

• Never use grinding/cutting discs with this tool

BEFORE USE

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Remove all obstacles on top of as well as underneath the

cutting path before you start cutting

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• 

or call the local utility company for assistance

(contact with electric lines can lead to re or electrical

shock; damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

DURING USE

• The noise level when working can exceed 85 dB(A); wear

ear protection

• Never use the tool without the original protection guard

system

• Do not attempt to cut extremely small workpieces

• Do not work overhead with the tool

• In case of jamming or electrical or mechanical

malfunction, immediately switch o the tool and

disconnect the plug

AFTER USE

• When you put away the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

a) 

and position your arms to resist kickback forces.

Position your body to either side of the blade, but

not in line with the blade. Kickback could cause the

saw to jump backwards, but kickback forces can be

controlled by the operator, if proper precautions are

taken.

b) When blade is binding, or when interrupting a cut

for any reason, release the trigger and hold the saw

motionless in the material until the blade comes to

a complete stop. Never attempt to remove the saw

from the work or pull the saw backwards while the

blade is in motion or kickback may occur. Investigate

and take corrective actions to eliminate the cause of

blade binding. Avoid cutting nails or screws.

c) When restarting a saw in the workpiece, centre the

saw blade in the kerf and check that saw teeth are

not engaged into the material. If saw blade is binding,

it may walk up or kickback from the workpiece as the saw

is restarted.

d) Support large panels to minimise the risk of blade

pinching and kickback. Large panels tend to sag under

their own weight. Supports must be placed under the

panel on both sides, near the line of cut and near the

edge of the panel.

e) Do not use dull or damaged blades. Unsharpened

or improperly set blades produce narrow kerf causing

excessive friction, blade binding and kickback.

f) Blade depth and bevel adjusting locking levers must

be tight and secure before making the cut. If blade

adjustment shifts while cutting, it may cause binding and

kickback.

g) Use extra caution when sawing into existing walls or

other blind areas. The protruding blade may cut objects

that can cause kickback.

3) LOWER GUARD FUNCTION

a) Check lower guard for proper closing before each

use. Do not operate the saw if lower guard does not

move freely and close instantly. Never clamp or tie

the lower guard into the open position. If the saw is

accidentally dropped, lower guard may be bent. Raise

the lower guard with the retracting handle and make sure

it moves freely and does not touch the blade or any other

part, in all angles and depths of cut.

b) Check the operation of the lower guard spring. If

the guard and the spring are not operating properly,

they must be serviced before use. Lower guard

may operate sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

c) Lower guard should be retracted manually only for

special cuts such as plunge cuts and compound

cuts. Raise lower guard by retracting handle and as

soon as blade enters the material, the lower guard

must be released. For all other sawing, the lower guard

should operate automatically.

d) Always observe that the lower guard is covering

the blade before placing the saw down on bench

 An unprotected, coasting blade will cause the

saw to walk backwards, cutting whatever is in its path. Be

aware of the time it takes for the blade to stop after switch

is released.

Рейтинг

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего Skil 2550 CA Циркулярная пила. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с Skil. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего Skil 2550 CA Циркулярная пила на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Все инструкции для Skil Циркулярные пилы
Больше руководств Циркулярные пилы

Часто задаваемые вопросы о Skil 2550 CA Циркулярная пила

Наша служба поддержки выполняет поиск полезной информации по изделиям и отвечает на часто задаваемые вопросы. Если вы заметили неточность в наших часто задаваемых вопросах, сообщите нам об этом с помощью нашей контактной формы.

Сопутствующие товары

Руководство

Skil 5265 AD Циркулярная пила

Руководство

Skil 3520 DC Циркулярная пила

Руководство

Skil 3551 CB Циркулярная пила

Руководство

Skil 5866 Циркулярная пила

Руководство

Skil 1052 Циркулярная пила

Руководство

Skil 5003 Циркулярная пила

Руководство

Skil 5740 CA Циркулярная пила

Руководство

Skil 3520 FA Циркулярная пила

Связанные категории