Руководство SentrySafe MS0200 Сейф

Руководство

ENGLISH

4

4-NUMBER COMBINATION

NOTE: Changing the combination voids your

warranty. To reinstate your Limited 1-Year

W

arranty, (valid purchase dated receipt

required) you must contact Sentry Customer

Service at the appropriate contact number on

the back cover to document your new

combination.

S

tart at zero.

Turn dial to left 4 rotations past ZERO. Stop

at the first number of your combination after

t

he fourth rotation.

Turn the dial to the right 3 rotations. Stop at

the second number on third rotation.

T

urn the dial to the left 2 rotations. Stop at

the third number on second rotation.

Turn the dial to the right. Stop at the last

number on first rotation.

To close and lock

1. Close door.

2. Turn door handle to the horizontal position.

3. Depress the key lock.

4. Spin the combination dial for greatest security.

Electronic lock

Battery installation

Four alkaline AA batteries, (not included) are required.

NOTE: Non-alkaline and rechargeable batteries

ARE NOT RECOMMENDED.

To install batteries: Turn the electric lock case to the

right and remove. (Fig. H) Insert four new batteries as

indicated, replace the electric lock case and turn to the

left to reassemble.

Safes with an

electronic and key lock

For added security, some models have a dual locking sys-

tem. You MUST use both the electronic code and the key

to open the safe.

To open your safe for the first time:

Install 4 AA batteries. (See instructions above.)

Turn the key to the right so that cylinder pops out. Enter

the electronic lock code printed on the back cover. When

the green PROCEED light comes on, you have four sec-

onds to turn the handle down to open.

Open first – test combination

with door open!

See back cover of this manual for your Factory Code.

NOTE: This combination cannot

be changed.

Using the keypad

Caution!

Liquids can damage the keypad!

Caution!

Pen points or other sharp objects can puncture

the keypad membrane!

Only a light touch is needed. A green PROCEED light

and a single beep indicate that the keypad “felt” your

touch. The lock allows 5 seconds for each key press.

After 5 seconds, 3 beeps will sound and a red light

will blink. Start over if this occurs.

Basic electronic lock

Access codes

There are three ways to unlock the safe.

1.

Enter the preset 5-digit electronic lock combination.

This code cannot be deleted and can always be

used to open the safe - keep it secure!

2. A 5-digit User Code of your choice can be pro-

grammed and changed as needed.

3. For temporary access to the safe, you can program

a 5-digit User PIN that can be erased or changed.

NOTE: All zeros is an invalid code.

Programminga5-digitUserCode

1. Press the Program key.

2. Enter the electronic lock combination. The

green LED remains ON while you enter the 5-

digit User Code of your choice. After 5 digits

are entered the green LED turns OFF.

To enter a new User Code, repeat these steps.

To erase the User Code, press the Program key

and enter your electronic lock combination

twice.

Programming a 5-digit User PIN

NOTE: You must program a User Code before

programming a User PIN.

1. Press the

Program

key.

2. Press it a second time.

3. Enter your 5-digit User Code. The green LED

remains ON.

4. Enter the 5-digit User PIN of your choice. After 5

digits are entered the green LED turns OFF.

(

To enter a new User PIN, repeat these steps. To

erase the User PIN, press Program twice, enter your

User Code and then enter 00000.)

Open first – test combination

with door open!

Test your new electronic lock combination several times

with the door open, to make sure you have recorded it

correctly. Your new electronic lock combination is

ready to use.

Record your User Code

and User PIN here

User Code: ____ ____ ____ ____ ____

User PIN: ____ ____ ____ ____ ____

To unlock safe:

Enter the preset 5-digit electronic lock combination,

a User Code, or a User PIN. When the green LED

lights you have 4 seconds to turn the handle and

open the safe.

To lock safe:

Close the door and return the handle to the horizontal

position.

Battery replacement

The yellow LED will light when the batteries need to be

replaced. No codes are erased when old batteries are

removed for replacement. See “Battery installation”

in the “Electronic lock” section for installation instructions.

NOTE: If your safe does not appear to be working,

please check batteries before calling Sentry

Customer Service.

NOTE: It is recommended you replace the batteries

after two years, or when the yellow LED

remains on.

Delay mode

The lock automatically enters a two-minute delay mode after

an invalid code has been entered three consecutive times. In

this mode, the lock can not be activated and any key entry

will generate an ERROR signal.

H

Рейтинг

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего SentrySafe MS0200 Сейф. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с SentrySafe. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего SentrySafe MS0200 Сейф на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Все инструкции для SentrySafe Сейфы
Больше руководств Сейфы

Часто задаваемые вопросы о SentrySafe MS0200 Сейф

Наша служба поддержки выполняет поиск полезной информации по изделиям и отвечает на часто задаваемые вопросы. Если вы заметили неточность в наших часто задаваемых вопросах, сообщите нам об этом с помощью нашей контактной формы.

Сопутствующие товары

Руководство

SentrySafe MSW0809 Сейф

Руководство

SentrySafe MS5635 Сейф

Руководство

SentrySafe MS0607 Сейф

Руководство

Rottner Monaco 45 Сейф

Руководство

Yale YSV/390/DB1 Сейф

Руководство

Chubb Executive 15E Сейф

Руководство

Yale YSV/170/DB1 Сейф

Руководство

Chubb AlphaPlus 6K Сейф

Связанные категории