Руководство Ryobi RCT18C-0 Циркулярная пила

Руководство

2 | English

wheel’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by

the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing

the wheel to climb out or kick out. The wheel may either jump

toward or away from the operator, depending on direction

of the wheel’s movement at the point of pinching. Abrasive

wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below.

■ Maintain a firm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided, for

maximum control over kickback or torque reaction

during start-up. The operator can control torque

reactions or kickback forces, if proper precautions are

taken.

■ Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

■ Do not position your body in line with the rotating

wheel. Kickback will propel the tool in direction opposite

to the wheel’s movement at the point of snagging.

■ Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory and cause loss

of control or kickback.

■ Do not attach a saw chain, woodcarving blade,

segmented diamond wheel with a peripheral gap

greater than 10 mm or toothed saw blade. Such

blades create frequent kickback and loss of control.

■ Do not “jam” the wheel or apply excessive pressure.

Do not attempt to make an excessive depth of cut.

Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the

cut and the possibility of kickback or wheel breakage.

■ When wheel is binding or when interrupting a cut

for any reason, switch off the power tool and hold

the power tool motionless until the wheel comes to

a complete stop. Never attempt to remove the wheel

from the cut while the wheel is in motion otherwise

kickback may occur. Investigate and take corrective

action to eliminate the cause of wheel binding.

■ Do not restart the cutting operation in the workpiece.

Let the wheel reach full speed and carefully re-enter

the cut. The wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

■ Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of the wheel.

■ Use extra caution when making a “pocket cut” into

existing walls or other blind areas. The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can cause kickback.

ADDITIONAL SAFETY WARNINGS

■ Clamp workpiece with a clamping device. Unclamped

workpieces can cause severe injury and damage.

■ Injuries may be caused, or aggravated, by prolonged

use of a tool. When using any tool for prolonged

periods, ensure you take regular breaks.

■ The product will restart automatically if stalled. Switch

off the product immediately if it stalls. Do not switch on

the product again while it is still stalled, as doing so

could trigger a sudden recoil with a high reactive force.

Determine why the product stalled and rectify this,

paying heed to the safety instructions.

■ Ambient temperature range for tool during operation is

between 0 ˚C and 40˚ C.

■ Ambient temperature range for tool storage is between

0 ˚C and 40˚ C.

■ The recommended ambient temperature range for the

charging system during charging is between 10 ˚C and

38˚ C.

ADDITIONAL BATTERY SAFETY WARNINGS

■ To reduce the risk of fire, personal injury, and product

damage due to a short circuit, never immerse your

tool, battery pack or charger in fluid or allow a fluid to

flow inside them. Corrosive or conductive fluids, such

as seawater, certain industrial chemicals, and bleach

or bleach-containing products, etc., can cause a short

circuit.

■ Ambient temperature range for battery during use is

between 0°C and 40°C.

■ Ambient temperature range for battery storage is

between 0°C and 20°C.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national

provisions and regulations.

Follow all special requirements on packaging and labelling

when transporting batteries by a third party. Ensure that

no batteries can come in contact with other batteries

or conductive materials while in transport by protecting

exposed connectors with insulating, non-conductive caps

or tape. Do not transport batteries that are cracked or

leaking. Check with the forwarding company for further

advice.

KNOW YOUR PRODUCT

See page 93.

1. Handle, insulated gripping surface

2. Hex key

3. Blade direction selector

4. Switch trigger

5. LED light

6. Spindle lock button

7. Wheel guard

8. Battery port

9. Cutting depth adjustment knob

10. Flange screw

11. Base support

12. Abrasive cut-off wheel

Рейтинг

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего Ryobi RCT18C-0 Циркулярная пила. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с Ryobi. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего Ryobi RCT18C-0 Циркулярная пила на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Все инструкции для Ryobi Циркулярные пилы
Больше руководств Циркулярные пилы

Часто задаваемые вопросы о Ryobi RCT18C-0 Циркулярная пила

Наша служба поддержки выполняет поиск полезной информации по изделиям и отвечает на часто задаваемые вопросы. Если вы заметили неточность в наших часто задаваемых вопросах, сообщите нам об этом с помощью нашей контактной формы.

Сопутствующие товары

Руководство

Ryobi RWS1400 Циркулярная пила

Руководство

Ryobi RWS1250 Циркулярная пила

Руководство

Ryobi CW-1801 Циркулярная пила

Руководство

Ryobi RTS18C-0 Циркулярная пила

Руководство

Ryobi W-1710 Циркулярная пила

Руководство

Ryobi RWS1600 Циркулярная пила

Руководство

Ryobi RCS18X-0 Циркулярная пила

Руководство

Интерскол ДП-190/1600М Циркулярная пила

Связанные категории