Руководство Ryobi RCS18X-0 Циркулярная пила

Руководство

the lower guard into the open position. If the saw is

accidentally dropped, lower guard may be bent. Raise

the lower guard with the retracting handle and make

sure it moves freely and does not touch the blade or any

other part, in all angles and depths of cut.

■ Check the operation of the lower guard spring. If

the guard and the spring are not operating properly,

they must be serviced before use. Lower guard may

operate sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

■ Lower guard may be retracted manually only for

special cuts such as “plunge cuts” and “compound

cuts”. Raise lower guard by retracting handle

and

as soon as blade enters the material, the lower

guard must be released. For all other sawing, the

lower guard should operate automatically.

■ Always observe that the lower guard is covering the

blade before placing saw down on bench or floor.

An unprotected, coasting blade will cause the saw to

walk backwards, cutting whatever is in its path. Be

aware of the time it takes for the blade to stop after

switch is released.

ADDITIONAL SAFETY WARNINGS

■ Do not use any abrasive wheels.

■ Use only blade diameter(s) in accordance with the

markings.

■ Identify the correct saw blade to be used for the material

to be cut.

■ Use only saw blades that are marked with a speed

equal or higher than the speed marked on the tool.

■ Use only saw blades recommended by the

manufacturer, which conform to EN 847-1, if intended

for wood and analogous materials.

■ Wear a dust mask.

■ Clamp workpiece with a clamping device.

Unclamped workpieces can cause severe injury and

damage.

■ Injuries may be caused or aggravated by prolonged use

of a tool. When using any tool for prolonged periods,

ensure you take regular breaks.

■ The product will restart automatically if stalled. Switch

off the product immediately if it stalls. Do not switch on

the product again while it is still stalled, as doing so

could trigger a sudden recoil with a high reactive force.

Determine why the product stalled and rectify this,

paying heed to the safety instructions.

■ Ambient temperature range for tool during operation is

between 0°C and 40°C.

■ Ambient temperature range for tool storage is between

0°C and 40°C.

■ The recommended ambient temperature range for the

charging system during charging is between 10°C and

38°C.

ADDITIONAL BATTERY SAFETY WARNINGS

■ To reduce the risk of fire, personal injury, and product

damage due to a short circuit, never immerse your

tool, battery pack or charger in fluid or allow a fluid to

flow inside them. Corrosive or conductive fluids, such

as seawater, certain industrial chemicals, and bleach

or bleach-containing products, etc., can cause a short

circuit.

■ Ambient temperature range for battery during use is

between 0°C and 40°C.

■ Ambient temperature range for battery storage is

between 0°C and 20°C.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national

provisions and regulations.

Follow all special requirements on packaging and labelling

when transporting batteries by a third party. Ensure that

no batteries can come in contact with other batteries

or conductive materials while in transport by protecting

exposed connectors with insulating, non-conductive caps

or tape. Do not transport batteries that are cracked or

leaking. Check with the forwarding company for further

advice.

KNOW YOUR PRODUCT

See page 82.

1. Hex key

2. Depth adjustment lock lever

3. Dust port

4. Spindle lock button

5. Handle, insulated gripping surface

6. Switch trigger

7. Lock-off button

8. Front handle, insulated gripping surface

9. Bevel adjustment knob

10. Edge guide knob

11. Battery port

12. Lower guard

13. Inner flange

14. Outer flange

15. Blade screw

16. Edge guide fence

17. Blade

18. Operator’s manual

19. Battery pack

20. Charger

MAINTENANCE

■ The product should never be connected to a power

supply when assembling parts, making adjustments,

cleaning, performing maintenance, or when the product

is not in use. Disconnecting the product from the power

supply will prevent accidental starting that could cause

serious injury.

■ When servicing, use only original manufacturer’s

replacement parts, accessories and attachments.

Use of any other parts may create a hazard or cause

product damage.

4

Original Instructions

Рейтинг

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего Ryobi RCS18X-0 Циркулярная пила. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с Ryobi. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего Ryobi RCS18X-0 Циркулярная пила на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Все инструкции для Ryobi Циркулярные пилы
Больше руководств Циркулярные пилы

Часто задаваемые вопросы о Ryobi RCS18X-0 Циркулярная пила

Наша служба поддержки выполняет поиск полезной информации по изделиям и отвечает на часто задаваемые вопросы. Если вы заметили неточность в наших часто задаваемых вопросах, сообщите нам об этом с помощью нашей контактной формы.

Сопутствующие товары

Руководство

Ryobi CW-1801 Циркулярная пила

Руководство

Ryobi RCT18C-0 Циркулярная пила

Руководство

Ryobi RTS18C-0 Циркулярная пила

Руководство

Ryobi W-1710 Циркулярная пила

Руководство

Ryobi RWS1400 Циркулярная пила

Руководство

Ryobi RWS1250 Циркулярная пила

Руководство

Ryobi RWS1600 Циркулярная пила

Руководство

Зенит ЗПЦ-2300 Циркулярная пила

Связанные категории