Руководство Ryobi EAG750RS Углошлифовальная машина

Руководство

1

English

GB

FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR

DESCRIPTION

1. Grinding wheel

2. Tool-less wheel guard

3. Auxiliary handle

4. Spindle lock button

5. Switch

6. Disc  ange

7. Clamp nut

8. Spindle shaft

9. Wrench

10. Wheel guard lock lever

11. Live tool indicator

SAFETY INSTRUCTIONS FOR ALL OPERATIONS

SAFETY WARNINGS COMMON FOR GRINDING OP-

ERATIONS:

 This power tool is intended to function as a grinder

tool. Read all safety warnings, instructions,

illustrations and specifications provided with this

power tool. Failure to follow all instructions listed

below may result in electric shock, fire and/or serious

injury.

 Operations for which the power tool was not

designed may create a hazard and cause personal

injury.

 Do not use accessories which are not specifically

designed and recommended by the tool

manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

 The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed

can break and fly apart.

 The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories cannot

be adequately guarded or controlled.

 The arbour size of wheels, flanges, backing pads

or any other accessory must properly fit the

spindle of the power tool. Accessories with arbour

holes that do not match the mounting hardware of the

power tool will run out of balance, vibrate excessively

and may cause loss of control.

 Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for

chips and cracks, backing pad for cracks, tear or

excess wear, wire brush for loose or cracked wires.

If power tool or accessory is dropped, inspect for

damage or install an undamaged accessory. After

inspecting and installing an accessory, position

yourself and bystanders away from the plane of

the rotating accessory and run the power tool at

maximum no-load speed for one minute. Damaged

accessories will normally break apart during this test

time.

 Wear personal protective equipment. Depending

on application, use face shield, safety goggles

or safety glasses. As appropriate, wear dust

mask, hearing protectors, gloves and workshop

apron capable of stopping small abrasive or

workpiece fragments. The eye protection must

be capable of stopping flying debris generated by

various operations. The dust mask or respirator must

be capable of filtrating particles generated by your

operation. Prolonged exposure to high intensity noise

may cause hearing loss.

 Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken accessory may fly away and

cause injury beyond immediate area of operation.

 Hold power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring or its

own cord. Cutting accessory contacting a “live” wire

may make exposed metal parts of the power tool “live”

and shock the operator.

 Position the cord clear of the spinning accessory.

If you lose control, the cord may be cut or snagged

and your hand or arm may be pulled into the spinning

accessory.

 Never lay the power tool down until the accessory

has come to a complete stop. The spinning

accessory may grab the surface and pull the power

tool out of your control.

 Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into

your body.

 Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing

and excessive accumulation of powdered metal may

cause electrical hazards.

 Do not operate the power tool near flammable

materials. Sparks could ignite these materials.

 Do not use accessories that require liquid

coolants. Using water or other liquid coolants may

result in electrocution or shock.

NOTE: The above warning does not apply for power

tools specifically designed for use with a liquid system.

Рейтинг

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего Ryobi EAG750RS Углошлифовальная машина. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с Ryobi. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего Ryobi EAG750RS Углошлифовальная машина на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Все инструкции для Ryobi Углошлифовальные машины
Больше руководств Углошлифовальные машины

Часто задаваемые вопросы о Ryobi EAG750RS Углошлифовальная машина

Наша служба поддержки выполняет поиск полезной информации по изделиям и отвечает на часто задаваемые вопросы. Если вы заметили неточность в наших часто задаваемых вопросах, сообщите нам об этом с помощью нашей контактной формы.

Сопутствующие товары

Руководство

Ryobi RAG18X-0 Углошлифовальная машина

Руководство

Ryobi RAG18125-0 Углошлифовальная машина

Руководство

Ryobi CG-11 Углошлифовальная машина

Руководство

Ryobi EAG2000RS Углошлифовальная машина

Руководство

Ryobi RAG18115-0 Углошлифовальная машина

Руководство

Ryobi EAG750RB Углошлифовальная машина

Руководство

Rodex RDX108 Углошлифовальная машина

Руководство

Вихрь УШМ-180/1800 Углошлифовальная машина

Связанные категории