Руководство Metabo SB 18 LTX BL I Дрель-шуруповерт

Руководство

ENGLISHen

14

accessory, the machine switches off automatically -

for better control of the machine and high user

protection compared to machines without this func-

tion.

The shutdown is indicated by a single red flashing of

the LED light (14) and a single beep.

7.2 Battery pack, capacity and signal

indicator Fig. B

Charge the battery pack before use.

Recharge the battery pack if performance dimin-

ishes.

Instructions on charging the battery pack can be

found in the operating instructions of the Metabo

charger.

7.3 Removing and inserting the battery pack

Fig. C

7.4 Setting the direction of rotation,

engaging the transporting safety device

(switch-on lock) Fig. D

7.5 Select the gear Fig. E

Do not set the gear switch (4) unless the motor

has stopped completely!

7.6 Set drill, hammer drill Fig. A

Activate slide switch (3).

7.7 Setting torque control, maximum torque,

pulse function

Do not work for long periods with pulse

function switched on! (The motor can

overheat.)

Fig. F

Set the desired operating mode at the setting wheel

(13):

1...10 = Torque control

= maximum torque

= Pulse function

7.8 Switching On/Off, setting the speed

Fig. A

Switching on, speed: press the trigger switch (15).

Press in the trigger switch to increase the

rotational speed.

Switching off: release the trigger switch (15). Note:

the noise that the machine makes when it

switches off is due to the design (quick stop)

and has no influence on the function or the

service life of the machine.

7.9 Keyless chuck Fig. G

With a soft tool shank, retightening may be required

after a short drilling period.

Instructions for machines with the designation

SB...:

1. The grating sound which may be heard after

opening the chuck is functional and is stopped

by turning the sleeve in the opposite direction.

2. Clamping the tool:

Turn sleeve in direction "GRIP, ZU" until the

noticeable mechanical resistance has been

overcome.

Caution! The tool is not yet clamped! Keep

turning the sleeve (it must "click" when

turning), until it cannot be turned any further -

only now is the tool securely clamped.

Cleaning: from time to time, hold the machine

vertically with the chuck facing downwards and

turn the sleeve fully in the direction "GRIP, ZU"

and then turn fully in the direction

"AUF, RELEASE". The dust collected falls from

the keyless chuck.

7.10 Chuck with quick-change system Quick

(for machines with the designation ...BL

Q...) Fig. H.

To remove: Push the interlock ring forward (a),

advance and pull off the chuck (b).

To fit: push the interlock ring forward and move the

chuck as far as the limit stop on the drill spindle.

7.11 Fitting the belt hook (equipment-

specific) / bit depot (equipment-specific)

Fig. I

Fit the belt hook (8) as shown.

Fit the bit depot (7) as shown.

8.1 Defective electronic safety shutdown

(...LTX BL...)

Red continuous lighting

of the LED lamp (14)

signals a defective safety shutdown.Have the

machine repaired. See chapter 10.

8.2 The machine's multifunctional

monitoring system

If the machine switches off automatically, the

machine electronics have activated automatic

protection mode. There will be a warning signal

(beep). The beeping stops after a maximum of 30

seconds or when the trigger switch (15) is released.

In spite of this protective function, overloading

is still possible with certain applications and

can result in damage to the machine.

Causes and remedies:

1. Battery pack almost empty Fig. A, B (The

electronics protect the battery pack against

damage through total discharge).

If one LED (11) is flashing, the battery pack is

almost flat. If necessary, press the button (10)

and check the LED lamps (11) to see the charge

level. If the battery pack is almost flat, it must be

recharged.

2. Long continuous overloading of the machine will

activate the temperature cut-out.

8. Troubleshooting

Рейтинг

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего Metabo SB 18 LTX BL I Дрель-шуруповерт. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с Metabo. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего Metabo SB 18 LTX BL I Дрель-шуруповерт на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Все инструкции для Metabo Дрели-шуруповерты
Больше руководств Дрели-шуруповерты

Часто задаваемые вопросы о Metabo SB 18 LTX BL I Дрель-шуруповерт

Наша служба поддержки выполняет поиск полезной информации по изделиям и отвечает на часто задаваемые вопросы. Если вы заметили неточность в наших часто задаваемых вопросах, сообщите нам об этом с помощью нашей контактной формы.

Сопутствующие товары

Руководство

Metabo SB 18 LTX-3 BL I Дрель-шуруповерт

Руководство

Metabo SB 18 LT Дрель-шуруповерт

Руководство

Metabo BS 18 Li Дрель-шуруповерт

Руководство

Metabo BS 18 LTX-3 BL I Дрель-шуруповерт

Руководство

Metabo SB 18 LTX-3 BL Q I Дрель-шуруповерт

Руководство

Metabo SB 18 LTX Impuls Дрель-шуруповерт

Руководство

Metabo BS 18 LTX Impuls Дрель-шуруповерт

Руководство

Metabo BS 18 LTX BL Quick Дрель-шуруповерт

Связанные категории