Руководство Metabo KHEV 5-40 BL Перфоратор

Руководство

ENGLISHen

10

This also applies to dust from other materials such

as some timber types (like oak or beech dust),

metals, asbestos. Other known diseases are e.g.

allergic reactions, respiratory diseases. Do not let

dust enter the body.

Observe the relevant guidelines and national

regulations for your material, staff, application and

place of application (e.g. occupational health and

safety regulations, disposal).

Collect the particles generated at the source, avoid

deposits in the surrounding area.

Use suitable accessories for special work. In this

way, fewer particles enter the environment in an

uncontrolled manner.

Use a suitable extraction unit.

Reduce dust exposure with the following measures:

- do not direct the escaping particles and the

exhaust air stream towards yourself or nearby

persons or towards dust deposits,

- use an extraction unit and/or air purifiers,

- ensure good ventilation of the workplace and keep

it clean using a vacuum cleaner. Sweeping or

blowing stirs up dust.

- Vacuum or wash protective clothing. Do not blow,

beat or brush protective gear.

See page 2.

1 Clamping knob *

2 Bow handle (additional handle) *

3 Additional handle *

4 Wing screw (for adjusting the depth stop) *

5Depth stop *

6 Tool lock

7Knob

8 Metabo VibraTech (MVT): integrated damping

system

9Trigger

10 Button for continuous operation (only in chisel

operating mode)

11 Handle

12 Electronic signal indicator

13 Operating indicator (light signal if mains power

is connected)

14 Button for reduced impact force (for working in

soft material)

* model-dependent, equipment-dependent

Before commissioning, check that the rated

mains voltage and mains frequency stated on

the type plate match your power supply.

Always install a universal current sensitive

ground fault circuit interruptor (type B RCD)

with a maximum trip current of 30 mA upstream.

Use only extension cables with a minimum cross-

section of 1.5 mm

2

. Extension cables must

correspond to the power consumption of the

machine (cf Technical Specifications). If a cable

roller is used, always roll up the cable completely.

6.1 Assembly of the bow handle or

additional handle

For safety reasons, always use the bow

handle (2) or additional handle (3) supplied.

MHEV...:

Release the clamping ring by turning the clamping

knob (1) anticlockwise. Adjust the bow handle (2) to

the required position and angle. Tighten the

clamping knob firmly.

KHEV...:

Open the clamping ring by turning the additional

handle (3) anticlockwise. Secure the additional

handle at the required angle. Tighten the additional

handle.

7.1 Depth Stop Setting

(Only for KHEV 5-40 BL)

Release the wing (4) screw. Set the depth stop (5)

to the required drilling depth. Retighten the wing

screw (4).

7.2 Positioning, removing tool

Before inserting, clean tool shank and apply

supplied special grease (accessories: Order

no. 6.31800)! Use only SDS-max tools.

Positioning tool:

Turn tool and insert until it engages. The tool is

automatically locked.

Pull on the tool to check that it is correctly

seated. (It must be possible to move the tool a

few centimetres in an axial direction.)

Remove the tool:

Pull the tool lock (6) backwards in direction

indicated by arrow (a) and remove tool (b).

7.3 Setting operating mode and chisel

position

Avoid levering with the machine when a chisel

is fitted.

Do not activate the switch button (7) until the

motor has completely stopped.

Turn the switch button (7) to select the desired

operating mode.

Impact drilling (only for KHEV...)

Chiselling

Setting which enables the chisel to be rotated

to the desired position.

Setting the position of the chisel:

The chisel can be

locked in different positions.

- Insert the chisel.

-Turn the knob (7) to the interim position .

- Turn the chisel to the required position.

- Turn the switch button (7) to position .

- Turn the chisel until it engages.

5. Overview

6. Initial Operation

7. Use

Рейтинг

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего Metabo KHEV 5-40 BL Перфоратор. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с Metabo. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего Metabo KHEV 5-40 BL Перфоратор на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Все инструкции для Metabo Перфораторы
Больше руководств Перфораторы

Часто задаваемые вопросы о Metabo KHEV 5-40 BL Перфоратор

Наша служба поддержки выполняет поиск полезной информации по изделиям и отвечает на часто задаваемые вопросы. Если вы заметили неточность в наших часто задаваемых вопросах, сообщите нам об этом с помощью нашей контактной формы.

Сопутствующие товары

Руководство

Metabo BHE 20 SP Перфоратор

Руководство

Metabo MHEV 11 BL Перфоратор

Руководство

Metabo PowerMaxx BH 12 BL 16 Перфоратор

Руководство

Metabo KHEV 8-45 BL Перфоратор

Руководство

Metabo BH 18 LTX BL 16 Перфоратор

Руководство

Metabo KHE 22 SP Перфоратор

Руководство

Metabo KHE 28 Перфоратор

Руководство

Metabo KHE 24 SP Перфоратор

Связанные категории