Руководство Lotus Professional enMotion Recessed Диспенсер бумажных полотенец

Руководство

ENGLISH

Congratulations on choosing to improve the hygiene

and cleanliness of your washroom. Lotus Professional’s

exciting new touchless recessed enMotion handtowel

dispensing system uses tomorrow’s innovation and

increased hand drying capacity to answer today’s need

for more efficient hygienic solutions. Your choice has

conveyed a commitment to providing a hygienic

washroom environment and a quality image, and to

improving the service in your washroom.

TOOLS AND SUPPLIES

• Screwdriver

• Power Drill

• Pencil or Pen

• Spirit level (recommended)

• 4 ea. #8 Wood Screws included

STEP ONE

Locate listed components:

• 1 enMotion recessed handtowel dispenser

• Dispenser Key

• 4 "D/LR21" Cell Batteries

• Instruction Guide

• Screws

STEP TWO

Assembling enMotion recessed handtowel dispenser

1. Locate key on right side of dispenser and open

dispenser.

2. Unwrap cellophane from batteries.

3. Load 4 “D” cell batteries in battery

compartment located in the rear of the

dispenser.

4. Close dispenser.

STEP THREE

Determining the wall location

1. Determine mounting location for dispenser.

When placing dispenser, allow at least

10 cm clearance on all sides.

2.

Notice the metal static ground clip on the

left side of the backplate. This must be in

contact with the wall to properly ground

the dispenser. Failure to properly ground

the dispenser will cause damage to the unit

and may cause unit to become inoperable.

3. If installing directly to the wall, a cut out of

38,1 cm high x 26,67 cm wide x 10,16 cm deep

will be required.

Notice: The door comes mounted on the

left side of the housing. If there is not

enough clearance for the door on the left,

refer to the directions below to switch the

door from the left to the right side.

Directions to switch door opening:

1. Use a Philips head screwdriver to remove the

silver hinges on the left side of the dispenser

and save the screws. Once removed, the hinges

should separate from the black back plate.

2. Next use a flat-head screwdriver to remove the

2 crescent push washers on the hinges so that

the door can be lifted off the hinges.

Save these washers.

3. Now use a Philips head screwdriver to remove

the lock assembly and move it to the opposite

side of the dispenser. Remove the silver cap

from the non-lock side and snap it into place on

the opposite side.

4. Finally, reattach the hinges, adding the push

washers from the previous step to ensure that

the door cannot be lifted off its hinges.

STEP FOUR

LOADING FIRST ROLL

(see step 1-4)

1. Place the roll as indicated at picture 1.

2. Lift the transfer bar and tuck the paper behind

it. Fold up 2,5 cm length of paper at the end of

the roll (transfer bar teeth should rest in crease).

3. With the transfer bar in place, press the blue

auto feed button on the lower right of the

dispenser (paper will be

automatically loaded).

4. Once the paper feeds through the bottom, tear

of the sheet and close the cover.

LOADING REPLACEMENT ROLLS

(see step 5 - 8)

5. When the low paper indicator is lit, add a new

paper roll.

6. Move the partial roll (approximately 7,5 cm

in Dia.) to the bottom roll holders (rewind any

excess paper back onto the roll).

7. Follow steps 1 through 2 to load a new roll in

the top bracket.

8. Close the cover.

Note: When the transfer option is used, the dispenser

will double feed paper toward the end of the partial

roll.

STEP FIVE

Operating the dispenser (see instructions on the inside

of the front cover)

1. Dispensing enMotion towels

A. In On-Demand Mode (ODM), wave hand

approximately 5 cm across front of the

dispenser. An enMotion towel will be dispensed.

B. In Hang Mode (HM) an enMotion towel will be

presented automatically, a few seconds after the

cover is closed or a towel is torn off.

C. Once towel is dispensed, a short delay will occur

to avoid paper waste. After the delay, the next

towel can be dispensed.

Note: To adjust the delay, see Step 6, "Adjusting

Settings".

2. Replacing batteries

A. The "low battery" light located on the right side

of the lens indicates that the battery power

is low.

Note: Once this light appears, dispenser

will continue to operate for a limited

period of time.

B. Replace batteries with 4 "D" cell batteries. Load

batteries as outlined in diagram located on

inside battery compartment.

3. Loading replacement rolls: see step 5.

4. Should you wave your hand 2-3 times inside the

sensor range and not receive a towel, open

cover and check to see if the paper is properly

loaded.

Then check inside the paper chute to see

if there is a jam. If necessary, clear the jam and

load paper properly. Once completed, close the

cover and the dispenser should function normally.

STEP SIX

Adjusting Settings

1. The enMotion Dispenser's "Adjustable Sheet

Length" (ASL) system allows for adjustments in

the towel length. The ASL system is located

inside the cabinet just to the right of the sensor.

Sizes are:

• Left setting - “S” Short towel

(maximum number of hand dries)

• Middle setting - “M” Medium towel

(optimal hand dry capacity)

• Right setting - “L” Long towel

(largest available towel)

Note: The ASL system is pre-set at the “L” option.

To change setting, locate the ASL

system inside the cabinet just to the right

of the sensor.

2. The enMotion Dispenser's "Adjustable Time

Delay" (ATD) system allows towels to dispense

at different time intervals after a towel is

removed from the dispenser. Settings are:

• Left setting - Short Delay

• Middle setting - Medium Delay

• Right setting - Long Delay

Note: The ATD system is pre-set at short

delay. To change setting, locate the ATD

system inside the cabinet just to the right

of the sensor.

3. The enMotion Dispenser's "Adjustable

Dispense Mode Range" (ADMR) system allows

for adjustment in how the towel is presented to

the end user.

Settings are:

• "ODM" - On-Demand Mode (the towel will

feed from the cabinet after the user has

activated the sensor)

• "HM" - Hang Mode (the towel will always be

showing. After tearing off one towel, another

towel will present itself.)

Note: The ADMR system is pre-set on the

On-Demand Mode. To change setting,

locate the ADMR system inside the cabinet

just to the right of the sensor.

= Battery

Рейтинг

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего Lotus Professional enMotion Recessed Диспенсер бумажных полотенец. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с Lotus Professional. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего Lotus Professional enMotion Recessed Диспенсер бумажных полотенец на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Все инструкции для Lotus Professional Диспенсеры бумажных полотенец
Больше руководств Диспенсеры бумажных полотенец

Сопутствующие товары

Руководство

Lotus Professional Marathon Диспенсер бумажных полотенец

Руководство

Lotus Professional nextTurn Диспенсер бумажных полотенец

Руководство

Lotus Professional enMotion Диспенсер бумажных полотенец