2 3
MEAT GRINDER
INSTRUCTION MANUAL
DESCRIPTION
(g. A)
1. On/Off/Reverse switch
2. Circuit Breaker/Reset switch
3. Locking knob
4. Head inlet
5. Head
6. Hopper plate
7. Food pusher
8. Snake
9. Cutting blade
10. Cutting plate (ne)
11. Cutting plate (medium)
12. Cutting plate (large)
13. Fixing ring
14. Kibbe attachment
15. Sausage attachments (ne/medium/large)
16. Body
IMPORTANT SAFEGUARD
• Home use only. Do not use for industrial
purpose.
• Unplug when assembling and
disassembling the unit.
• Close supervision is necessary when any
appliance is used near children.
• When carrying the unit be sure to hold the
head with one hand, and the back knob
with the other hand. Do not carry the unit
by the hopper plate or head.
• Do not x the cutting blade and cutting
plate when using kibbe attachment.
• Under load continuous running of meat
grinder should be not more than 10-15
minutes with the following 10 minutes
interval for motor cooling.
• To avoid jamming, do not force to operate
the unit with excessive pressure.
• Never try to replace the parts and repair
the unit by yourself.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for
their safety.
• Children should be supervised to ensure
that they do not play with the appliance.
BEFORE ThE FIRST USING
• Check that voltage indicated on the rating
label corresponds the mains voltage in
your home.
• Wash all parts (except body) in warm
soapy water.
• Before plugging in, ensure the Off/
Reverse switch is „Off“ position.
• When the motor activates, do not switch
on.
• Never try to replace the parts and repair
the unit by yourself.
INSTRUCTION FOR USING
ASSEMBLING
Appliance will cut off power when the current
is over 1.5 times rated current, after around
3 seconds, press Circuit breaker&Reset to
reset, then press “ON”, the appliance can
continue to work.
• Hold the head and insert it into the
inlet(when inserting pls pay attention
the head must be slanted as per arrow
indicated on the top, see g.1),then move
the head anticlockwise so that the head
being fastened tightly. (g. 2)
• Place the snake into the head, long end
rst, and turn to feed the screw slightly
until it is set into the motor housing
(g. 3).
• Place the cutting blade onto the snake
shaft with the blade facing the front as
illustrated. If it is not tted properly, meat
will not be ground (g. 4).
• Place the desired cutting plate next to the
cutting blade, tting protrusions in the slot
(g. 5).
• Screw the xing ring tight. Do not over
tighten (g. 6).
• Place the hopper plate on the head and
x it into position.
• Locate the unit on a rm place.
• The air passage at the bottom and the
side of the motor housing should be kept
free and not blocked.
MINCING MEAT
• Cut all foods into pieces so that they t
easily into the hopper opening.
• Plug and switch on machine.
• Feed foods into the hopper plate. Use for
it only the food pusher (g. 7).
• After use switch the unit off and unplug it
from the power supply.
REVERSE FUNCTION
• After using, Press “OFF&REVERSE” to
let appliance to stop, then pull plug out.
• If blockade is happened, direct press
“OFF&REVERSE” for 3-6 seconds.
• After unblocking, release
“OFF&REVERSE”, and pull plug out, then
clean food out from head of appliance.
MAKING KIBBE
• Mince meat three times and mix all
ingredients together in a bowl. More
meat and less our for outlet cover create
better consistency and taste.
• Grind the mixture three times.
• Disassemble by reversing the steps form
assembling 5-3 to remove the cutting
plate and cutting blade
• Place kibbe attachments A and B onto
the feed screw shaft together, tting
protrusions in the slots. (g. 8)
• Screw cap into place until tight. Do not
over tighten (g. 9).
• Make the cylindrical outlet cover (g. 10).
• Form kibbe as illustrated below and deep
fry.
MAKING SAUSAGE
Before starting please assemble sausage
attachment as per following (g. 11)
CLEANING AND MAINTENANCE
DISASSEMBLING (g. 12/13)
• Make sure that the motor has stopped
completely.
• Disconnect the plug from the power
outlet.
• Disassemble by reversing the steps from
assembling.
CLEANING
• Remove meat, etc.
• Wash each part in warm soapy water.
• A bleaching solution containing chlorine
will discolor aluminum surfaces.
• Do not immerse the motor housing in
water, but only wipe it with a damp cloth.
• Thinners and petrol will crack of change
the color of the unit.
• Wipe all the cutting parts by vegetable
oil-wet cloth.
PACKAGING
• After cleaning, put cordset into cordset
box which is on back of appliance Body
(see Illustration 14)
• Then lock the cover of cordset box. (see
Illustration 15)
Put 2 blade trays and 2 kibbes in the
storage lid which is on appliance body.
(see Illustration 16)
• Adjust the position of 2 kibbes, then cover
the storage cover, or it is very difcult to
cover the storage cover. (g. 17)
SPECIFICATION
Rating: 220-240V, 50Hz
Power: 700W Nominal/1800W Maximal
Net/Gross Weight: 5.8kg/6.0kg
Overall Dimension: 410mmx290mmx258mm
(LxDxH)
Environment friendly disposal
You can help protect the environment! Please
remember to respect the local regulations:
hand in the non-working electrical
equipments to an appropriate waste disposal
center.
ENGLISh
ENGLISh
Присоединиться к беседе по данному изделию
Здесь вы можете поделиться тем, что думаете о First Austria FA-5140 Мясорубка. Если у вас есть вопросы, сначала внимательно прочтите инструкцию. Запросить руководство можно с помощью контактной формы.