Руководство FERM GSM1001 Садовый измельчитель

Руководство

Ferm 61

• Dress sensibly for the job in hand - no loose clot-

hing that could get caught in the moving parts of

the appliance.

• Always wear safety goggles and a dust mask when

using this appliance.

• Always wear heavy-duty outdoor gloves when

using the appliance.

• Pull long hair back out of the way and wear a pro-

tective hat.

• Guard against electric shock - prevent body con-

tact with earthed or grounded surfaces i.e. metal

gates, posts or other metal objects in the work

area.

• Never pull the appliance by its power cord. Wheel

it or carry it with two hands.

•Do not allow the power cord to lay on or across

sharp objects that might pierce the outer insula-

tion. Carry out a visual inspection of the power

cord before use and if it is damaged, have it

replaced by a specialist service centre. Do not use

the appliance if the cord is damaged.

• Keep the power cord away from heat, frost, oil,

solvents or any sharp objects or edges.

Do not use this appliance if you are on strong medica-

tion, unwell or have been drinking alcohol.

ELECTRICAL INFORMATION

Check that the mains power supply corresponds

to the voltage printed on the appliance rating

plate.

IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN

All electrical connections e.g. extension cable, must be

of an approved waterproof type for outdoor use and

marked accordingly. Extension cables must be three-

core, one of which is EARTH.

Always fully unwind extension cables before use.

ASSEMBLY (fig. 3+4)

Step 1. Attach the legs to the shredder using 4 hex

bolts and tighten with allen key supplied.

Step 2. Attach wheels to legs. Feed spindle through

legs, add spacers at both ends and attach wheels using

a spring clip and washer.

Step 3. Place upright and push-fit wheel caps.

GENERAL USE

WARNING!

NEVER ATTEMPT TO PUT YOUR HAND INSIDE

THE SHREDDER INLET CAVITY. IF YOU WANT TO

PUSH MATERIAL INTO THE CUTTING CHAMBER

USE A SUITABLE STRONG STICK!

• Before starting the machine, look into the feeding

chamber to make certain that it is empty.

• Keep your face and body away from the feed inta-

ke opening.

• Do not allow hands or any other part of the body

or clothing inside the feeding chamber, discharge

chute, or near any moving part.

• Keep proper balance and footing at all times.

Do not overreach. Never stand at a higher level

than the base of the machine when feeding material

into it.

• Always stand clear of the discharge zone when

operating this machine.

• When feeding material into the machine be extre-

mely careful that pieces of metal, rocks, bottles,

cans or other foreign objects are not included.

• If the cutting mechanism strikes any foreign objects

or if the machine should start making any unusual

noise or vibration, shut off the power source and

allow the machine to stop (electric unit disconnect

from supply):

•inspect for damage

• check for and tighten any loose parts

• have any damaged parts replaced or repaired

with parts having equivalent specifications

• Do not allow processed material to build up in the

discharge zone; this may prevent proper discharge

and can result in kickback of material through the

feed intake opening.

•If the machine becomes clogged, shut-off the

power source (electric unit disconnect from sup-

ply) before clearing debris. Keep the power source

clear of debris and other accumulations to prevent

damage to the power source or possible fire.

Remember that operating the starting mechanism

on engine powered machines will still cause the

cutting means to move.

• Keep all guards and deflectors in place and in good

working condition

• Do not tamper with the power source governor

settings; the governor controls the safe maximum

operating speed and protects the power source

and all moving parts from damage caused by over-

speed. Seek authorised service if a problem exists.

• Do not transport this machine while the power

source is running.

• Shut off the power source and disconnect from

supply whenever you leave the work area.

• Do not tilt the machine while the power source is

running.

Your shredder must be placed on firm, level ground.

Never lay the shredder on its back, front or sides -

keep it upright at all times.

Do not overload the shredder - feed it slowly and let

it work at its own pace.

Before use, ensure the inlet cavity is empty. Do not

start the shredder with material in the shredder.

Unless there is an emergency, do not switch the

shredder off until it is completely empty of material.

Remove stones or other hard objects from plant roots

before shredding.

4 Ferm

Рейтинг

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего FERM GSM1001 Садовый измельчитель. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с FERM. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего FERM GSM1001 Садовый измельчитель на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Все инструкции для FERM Садовые измельчители
Больше руководств Садовые измельчители

Часто задаваемые вопросы о FERM GSM1001 Садовый измельчитель

Наша служба поддержки выполняет поиск полезной информации по изделиям и отвечает на часто задаваемые вопросы. Если вы заметили неточность в наших часто задаваемых вопросах, сообщите нам об этом с помощью нашей контактной формы.

Сопутствующие товары

Руководство

FERM GSM1002 Садовый измельчитель

Руководство

Atika AMA 2300 Садовый измельчитель

Руководство

Viking GE 103 Садовый измельчитель

Руководство

Makita UD2500 Садовый измельчитель

Руководство

Viking GE 260 S Садовый измельчитель

Руководство

AL-KO MH 2500 Slice Садовый измельчитель

Руководство

Solo TCS Duotec 2500 Садовый измельчитель

Руководство

Viking GE 101 Садовый измельчитель

Связанные категории