Руководство FERM BGM1022 Ленточно-шлифовальная машинка

Руководство

7

EN

for finishing. The sanding needs to be continued

until the surface is smooth.

The placing of the sanding paper

Fig. F - H

When the sanding machine is held with the

sanding disc turned towards you, the sanding belt

moves from right to left along the upper part of

the machine. Because of this turning direction the

workpiece will be pressed against the right side

of the fence. An arrow on the inside indicates the

right direction of running of the sanding belt (see

drawing). If no direction is indicated, the sanding

belt must be placed in such a way that the elevated

part of the seam is placed into the turning direction

of the belt. So it is very important that the sanding

belt is placed in the correct way. The machine uses

standard 100 x 915 mm sanding belts (6):

• Remove the plug from the mains socket.

• Push the clamping handle completely to the

right to take away the tension of the transport

rollers (4).

• Push the sanding belt along both of the

transport rollers, starting from the back of the

machine.

• Push the clamping handle completely to the

left. Now the sanding belt should be completely

tight.

• Turn the transport roller exactly in a right angle

to the direction of the sanding belts with the

use of the winged nut at the right roller. The

direction of running of the belt is adjusted

correctly if the sides of the sanding belt are

running parallel to the bearing plate.

The sanding disc

Fig. D

Paper or “velcro” plates are used for the sanding

disc. The standard diameter is 150 mm. The

plates are self adhesive .

Vertical placing of the sanding belt

Fig. I

For more flexibility of the sanding belt its bottom

side can be used, because there is no bearing

plate. For an easy reach of this bottom side the

sanding belt can be placed in vertical position.

• Loosen the two nuts at the front of the sanding

machine, around the left transport roller shaft,

with the use of an open-end spanner.

• Push the sanding belt up in the position

desired. Fasten the two nuts again.

• The workpiece can now rest on the worktop

instead of on the sanding belt;

• The work plate which is used for the sanding

disc can now be pushed with the shaft into the

hole of the machine frame, at the left side of

the sanding machine.

• Fasten the bolt at the back of the machine.

• The work plate can now be used as support

for the sanding of the work piece against the

sanding belt.

4. OPERATION

Always stand facing the machine so that

you always have a good overview (Fig.

A).

Switching On/Off

• Press the switch into position ‘1’ to put your

sanding machine into operation.

• To switch off the machine the same switch

needs to be pressed to position ‘0’. Always

keep the mains cable away from moving parts.

• There is no need to apply any pressure with

the workpiece, because this only slows down

the speed of the sanding disc.

Sanding

The sanding belt and disc supplied with this

sanding machine are suitable for the sanding of

metal, wood or synthetic surfaces. The workpiece

should always be held firmly during sanding. No

extra pressure is needed. Guide the work piece

up and down over the sanding belt, in order to

prevent the sanding belt and plate from wearing

through in one place. Round objects can be

sanded at the ends of the sanding belt. Work

pieces which are longer than the sanding machine

can be sanded by removing the fence.

NB: To prevent splintering, wood always needs

to be sanded in the longitudinal direction of the

grain.

To treat a very soft surface, there is a very handy

method to ‘bring the particles to the surface’.

This is done as follows: wet the already sanded

surface with a cloth or sponge and let it dry well.

Some wood fibres will swell up more than others,

which leads to a rougher surface than before.

Now the higher particles are treated with fine

sanding paper, the result is a remarkably smooth

surface. This method should not be applied with

Рейтинг

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего FERM BGM1022 Ленточно-шлифовальная машинка. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с FERM. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего FERM BGM1022 Ленточно-шлифовальная машинка на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Все инструкции для FERM Ленточно-шлифовальные машины
Больше руководств Ленточно-шлифовальные машины

Часто задаваемые вопросы о FERM BGM1022 Ленточно-шлифовальная машинка

Наша служба поддержки выполняет поиск полезной информации по изделиям и отвечает на часто задаваемые вопросы. Если вы заметили неточность в наших часто задаваемых вопросах, сообщите нам об этом с помощью нашей контактной формы.

Сопутствующие товары

Руководство

FERM BSM1021 Ленточно-шлифовальная машинка

Руководство

FERM BSM1001 Ленточно-шлифовальная машинка

Руководство

FERM BSM1024 Ленточно-шлифовальная машинка

Руководство

FERM BGM1003 Ленточно-шлифовальная машинка

Руководство

FERM EFM1001 Ленточно-шлифовальная машинка

Руководство

FERM BSM1002 Ленточно-шлифовальная машинка

Руководство

FERM BGM1001 Ленточно-шлифовальная машинка

Руководство

FERM BSM1005 Ленточно-шлифовальная машинка

Связанные категории