Руководство Casals VSC65 Циркулярная пила

Руководство

Once you have nished using the appliance:

- Stop the appliance by releasing the on/off switch.

Maintenance and care

WARNING! Always unplug the machine before carrying

out work on it.

- Checking the saw blade: deposits of resin and glue

on the saw blade cause inefcient cutting. To avoid them,

always clean the blade immediately after use.

- Inspect the mounting screws: regularly inspect all the

mounting screws and ensure they are rmly tightened.

Should any screw be loose, tighten it immediately. Failure

to do so could put you at serious risk.

- Motor maintenance: always take the greatest care

over this and make sure that the motor winding is not

damaged and does not become wet with oil or water.

- The vents should always be kept clean and free of

obstacles.

- Clean the machine thoroughly after each use. Blast the

motor regularly with compressed air.

- Check that the mains lead is in good condition. If it

is not, take it to an Ofcial Service Centre to have it

replaced.

Cleaning

- Disconnect the appliance from the mains and allow it

to cool before undertaking any cleaning task.

- Clean the electrical equipment and the mains

connection with a damp cloth and dry. DO NOT

IMMERSE IN WATER OR ANY OTHER LIQUID.

- Clean the equipment with a damp cloth with a few

drops of washing-up liquid and then dry.

- Do not use solvents, or products with an acid or base

pH such as bleach, or abrasive products, for cleaning

the appliance.

- Do not let water or any other liquid get into the air

vents to avoid damage to the inner parts of the

appliance.

- Never submerge the appliance in water or any other

liquid or place it under running water.

- If the appliance is not in good condition of cleanliness,

its surface may degrade and inexorably affect the

duration of the appliance’s useful life and could

become unsafe to use.

- CAUTION: There is a risk of re if the appliance’s

cleaning is not done according to these instructions.

Supplies

- Always use original supplies, designed specically

for your appliance model.

- These supplies are available in specialist shops.

6

soon as blade enters the material, the lower guard must

be released. For all other sawing, the lower guard should

operate automatically.

- Always observe that the lower guard is covering the

blade before placing saw down on bench or oor. An

unprotected, coasting blade will cause the saw to walk

backwards, cutting whatever is in its path. Be aware of the

time it takes for the blade to stop after switch is released.

Product description and Specications

Description

A

HM saw blade

B Spindle blocking button

C Mobile blade guard

D Saw blade setting disc

E Disc setting screw

F Depth setting wing nut

G Lateral stop setting wing nut

H Safety push button switch

I On-/off switch

J Angular cutting wing nut

K Cutting line guide

L Sawdust extraction

M Lateral Stop

Instructions for use

Before use:

- Make sure that all the product’s packaging has been

removed.

- Ensure that the voltage indicated on the rating label

matches the mains voltage before plugging in the

appliance.

- Prepare the appliance according to the function you

wish to use:

Fitting the disc

- Unplug the appliance from the mains before replacing

any accessory.

WARNING! : Always unplug the machine before carrying

out any work on it.

CAUTION: Do not use bent or cracked blades or high-

speed steel blades. Do not use saw blades that do

not conform to the specications contained in these

instructions.

WARNING! Never press the blocking button B when

the machine is running. The shaft must have stopped

completely before the blocking button B is pressed.

1. Move the mobile guard (C) backwards and hold

it in place.

2. To loosen or tighten screw (E), block the screw

press by pushing block button (B).

3. Loosen the screw (E) and remove the setting

disc (D).

4. Fit the saw blade and tighten with the setting disc

(D) and the screw (E).

4.1 To adapt saw discs with a 30mm hole diameter,

rst t the washer that corresponds to the diameter

of the saw disc you are using, next the saw disc

and screw them into place with fastening disc D and

screw E.

5. Before tting the new blade, make sure the

surfaces in contact with the setting discs are clean.

(The arrow printed on the xed guard of the machine

indicates the cutting direction of the teeth).

6. Once the disc is tted, check that the blocking

button (B) has returned to its original position due to

movement of the incorporated spring.

- In order to remove disc, follow the same steps as

indicated previously but in reverse order.

Dust extraction Assembly

- Always use the appliance with the dust collector

connected, inhaling dust is harmful to your health.

- Connect the vacuum aspirator suction tube to the dust

extraction adaptor (L)

Use:

Cutting depth setting

- To adjust the cutting depth, loosen the wing nut (F) and

move the base upwards or downwards. The scale printed

on the base indicates the cutting depth

Cutting angle setting

It can cut vertically and with an inclination of up to 45º.

The angle is adjusted by loosening the wing nut (J) and

according the scale printed on the base.

Cutting indication

The notch K is used as a cutting indication with the blade in

a vertical position or 45º. It is advisable to make test cuts.

Lateral stop adjustment

For parallel cutting, use the lateral stop (M). Cutting width

is adjusted with the scale or according to the plotting.

Tighten the wing nut (G) to work with the lateral stop.

- Connect the appliance to the mains.

- Press the locking button (H), and squeeze the trigger in

the on/off switch (I). When the on/off switch is released, the

machine stops.

Рейтинг

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего Casals VSC65 Циркулярная пила. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с Casals. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего Casals VSC65 Циркулярная пила на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Все инструкции для Casals Циркулярные пилы
Больше руководств Циркулярные пилы

Часто задаваемые вопросы о Casals VSC65 Циркулярная пила

Наша служба поддержки выполняет поиск полезной информации по изделиям и отвечает на часто задаваемые вопросы. Если вы заметили неточность в наших часто задаваемых вопросах, сообщите нам об этом с помощью нашей контактной формы.

Сопутствующие товары

Руководство

Casals CCS190L Циркулярная пила

Руководство

Rodex RDX3821 Циркулярная пила

Руководство

Зенит ZPC-2300 Циркулярная пила

Руководство

Интерскол ДП-210/1900М Циркулярная пила

Руководство

Skil 3540 FA Циркулярная пила

Руководство

Redverg RD-CS150-66L Циркулярная пила

Руководство

Redverg RD-CS130-55 Циркулярная пила

Руководство

Alteco CS 0510 Циркулярная пила

Связанные категории