Руководство Camry CR 4812 Мясорубка

Руководство

4

23.Do not clean the equipment while mounted on the machine's drive assembly.

Max. power:1600W

Power: 500W

Supply voltage: 220-240V ~50/60Hz

Break time before another use: 30 minutes

Permitted continuous operation time: 10 minutes

TECHNICAL DATA

5.Don't clean the equipment mounted on the machine's drive assembly.

4.Do not wash the metal parts in dishwashers. Strong cleaning agents used in dishwashers cause the metal parts to turn black.

Handwash the metal parts using traditional washing-up liquid.

3.Clean the metal parts with soft brush.

2.Do not clean the casing using strong detergents in the form of emulsion, lotion, paste etc.

1.Don't immerse grinder in water or other liquids.

CLEANING AND MAINTENANCE

In case some bone is too hard, it is normally the plastic clutch (9) broken but not the motor. In set is added one extra 1 pcs plastic clutch

that should be replaced by end user. Unscrew the screw inside the plastic coupling (9) using a screwdriver, replace the plastic part and

then screw it back on again.

SCREW COUPLER REPLACEMENT

4. Form Kebbe as illustrated on figure 4 and deep fry.

3. Put the previously prepared mixture to be ground into grinding chamber, shoving them with the pusher (5).

2. Assemble the set according to figure 4.

1. Mince the meat three time and mix all ingredients together in a bowl. Grind the mixture three times.

The attachment is used for in-house KEBBE preparation.

KEBBE ATTACHMENT

3.Put the wet rounds on the outside of sausage attachment, gently slide down during stuffing, and wind for preferred length.

2.Soak the previously prepared intestine casings (called rounds) in warm water for about 30 minutes before stuffing.

1.Assemble the set according to figure 4.

The attachment is used for in-house sausage production.

SAUSAGE ATTACHMENT

4.Turn the device off by pressing the button (2 - OFF).

3.If needed, you can turn on reverse rotations by pushing the button (2 - R).

2.Put the previously prepared products to be ground into grinding chamber, shoving them with the pusher (5).

1.Turn the device on by pressing the button (2 - ON) – forward.

DEVICE OPERATION

7. drive assembly head 8. screw 9. screw coupler

10. knife 11. 3 hole sleeves (3 mm, 5 mm, 7 mm) 12. nut

13. sausage/butcher attachment 14a, 14b kebbe attachment 15. lid of storage box

In order to assembly the grinding chamber (3), insert the elements in following order:

DEVICE DESCRIPTION

Grinding assembly (fig 2)

1. machine body 2. power switch (ON/OFF) / reverse button (R) 3. grinding chamber

4. tray 5. pusher 6. grinding chamber lock button

PREPARING MEAT GRINDER FOR OPERATION

26.Do not grind dry poppy seed. The poppy seed needs to be steamed and soaked before

grinding.

25.Do not wash the metal parts in dishwashers. Aggressive cleaning agents used in

dishwashers cause the metal parts to turn black. Handwash the metal parts using

traditional washing-up liquid. Use soft brush.

24.Don't use aggressive detergents to clean the housing, as it may remove the

informational graphic symbols such as: scale, signs, safety marks,Etc.

22.Do not immerse the drive assembly in water, don't clean it under running water.

5.Mount the tray (4) on top of the grinding chamber.

4.Mount the assembled grinding part in the drive, so that the coupler (9) fits the drive head (7). Press in the grinding part, and rotate

counter clockwise until vertical. Audible click is heard when the assembly is mounted correctly. Tighten nut (12) on the grinding chamber

(3).

3.Check if the grinding chamber is complete. If not, assembly the chamber using all elements, according to figure 2.

2.Before use wash the grinding chamber with all elements, tray and pusher.

1.Place the machine body on even, hard surface, so that the ventilation holes are not covered, and close to power outlet

PREPARATION OF GRINDER

- Gently tighten the assembly with the nut (12)

- Then one of hole plates (11), with the chamber protrusion matching the groove on the outside edge of the plate

- Knife (10) onto screw pin, with blades facing the hole plate

- Screw (8)

Рейтинг

Подробнее об этом руководстве

Мы понимаем, что приятно иметь бумажное руководство для вашего Camry CR 4812 Мясорубка. Вы всегда можете скачать инструкцию с нашего сайта и распечатать самостоятельно. Если вы хотите получить оригинальное руководство, мы рекомендуем вам связаться с Camry. Возможно, они смогут предоставить оригинальное руководство. Вы ищете руководство для вашего Camry CR 4812 Мясорубка на другом языке? Выберите предпочитаемый язык на нашей домашней странице и найдите номер модели, чтобы узнать, есть ли она у нас в наличии.

Технические характеристики

Все инструкции для Camry Мясорубки
Больше руководств Мясорубки

Часто задаваемые вопросы о Camry CR 4812 Мясорубка

Наша служба поддержки выполняет поиск полезной информации по изделиям и отвечает на часто задаваемые вопросы. Если вы заметили неточность в наших часто задаваемых вопросах, сообщите нам об этом с помощью нашей контактной формы.

Сопутствующие товары

Руководство

Camry CR 4810 Мясорубка

Руководство

Stollar BMG900 Мясорубка

Руководство

Stollar BMG500 Мясорубка

Руководство

УМНИЦА МЭ-3600Вт Мясорубка

Руководство

Stollar BMG740 Мясорубка

Руководство

Supra MGS-2003 Мясорубка

Руководство

BBK MG1506 Мясорубка

Руководство

Gorenje MG1500XG Мясорубка

Связанные категории